jproy
09-15-2009, 08:33 PM
Hello all,
I just went to a meet last night for a bunch of Subi guys and was the lone J32 in the lot. It was fun though. Good convo with some good guys. I was recomended to the board through David at HybridRacing here in Baton Rouge. I have done quite a bit of work on the J32, own aluminum welding TIG and MIG, and do fabrication in my spare time.
The car is a 2003 CL-S 6 speed manual NPB---
I currently have done to the car;
1. Port match and polish all parts of the intake system,
2. Comptech/custom intake system
3. Walborow 255lph fuel pump
4. Aeromotive FPR with AN-6 fittings and braided plumbing
5. Custom Comptech headers
6. Outlaw Engineering Upper intake manifold spacer
7. lightweight crank pulley
8. RT 7000 cat
9. Custom 2.5" exhaust
10. Autometer wideband A/F
11. Autometer boost vac/gauge
12. RC440 fuel injectors
13. Rotora 13" BBK
14. '05 Acura TL wheels
15. H&R springs
16. Tokico Ilumina adjustable shocks
17. 60A custom poly engine mounts
18. Corsport shifter linkage solid bushings.
19. AEM FIC-6
20. Custom Paul Smalser PnP wire harness
21. UR crank pulleys
22. 4th Generation MP90 supercharger custom fit in place of MP62 from the Comptech supercharger kit for the CL-S.
23. Currently developing a air to water intercooler system for the setup. I have all the parts in hand but need to finish fabricating all the parts with the TIG welder. Its taking a while with work and day to day life.
Thats all I can remember that I have done to the car at the moment. If anyone has any questions or would like to meet up please dont hesitate to drop a line. There is very little I dont know about everything on this car.
Best Regards,
Jim :cool:
I just went to a meet last night for a bunch of Subi guys and was the lone J32 in the lot. It was fun though. Good convo with some good guys. I was recomended to the board through David at HybridRacing here in Baton Rouge. I have done quite a bit of work on the J32, own aluminum welding TIG and MIG, and do fabrication in my spare time.
The car is a 2003 CL-S 6 speed manual NPB---
I currently have done to the car;
1. Port match and polish all parts of the intake system,
2. Comptech/custom intake system
3. Walborow 255lph fuel pump
4. Aeromotive FPR with AN-6 fittings and braided plumbing
5. Custom Comptech headers
6. Outlaw Engineering Upper intake manifold spacer
7. lightweight crank pulley
8. RT 7000 cat
9. Custom 2.5" exhaust
10. Autometer wideband A/F
11. Autometer boost vac/gauge
12. RC440 fuel injectors
13. Rotora 13" BBK
14. '05 Acura TL wheels
15. H&R springs
16. Tokico Ilumina adjustable shocks
17. 60A custom poly engine mounts
18. Corsport shifter linkage solid bushings.
19. AEM FIC-6
20. Custom Paul Smalser PnP wire harness
21. UR crank pulleys
22. 4th Generation MP90 supercharger custom fit in place of MP62 from the Comptech supercharger kit for the CL-S.
23. Currently developing a air to water intercooler system for the setup. I have all the parts in hand but need to finish fabricating all the parts with the TIG welder. Its taking a while with work and day to day life.
Thats all I can remember that I have done to the car at the moment. If anyone has any questions or would like to meet up please dont hesitate to drop a line. There is very little I dont know about everything on this car.
Best Regards,
Jim :cool: